![]() ![]() If you are not familiar with setting the menu options in your radio, you will need to read Section 12 Set Mode of the IC-7300 FULL manual PDF. There are several menu items in the radio which must be set correctly in order for HRD to communicate with the radio once connected to the computer. Once you have determined which Com Port/Ports are used by the IC-7300, make a note of the port number and proceed to Step#2. ![]() The other end of the USB cable goes to a USB Port on the computer. USB (B) is located on the lower right side of the radio when viewing the radio from the back. ![]() Once the driver is installed on your computer, connect the USB cable to USB (B) on the back of the radio. Once you have downloaded the driver, read the installation manual and carefully follow the instructions for the installation of the driver prior to installing and connecting the USB cable between the radio and the computer. The file your looking for is used by several Icom radios, so read carefully and be certain you select the file name: USB Driver(Ver.1.20), Driver Utility and manuals dated 1. To connect the IC-7300 to your computer and HRD using the USB cable requires installing a USB Virtual Com Port driver which can be downloaded from the Icom website. To download the manual, copy and paste the link below into the address bar of your favorite web browser. If you don't have the complete manual for your IC -7300, it can also be downloaded from the following link. You may need the IC-7300 manual to learn how to access the radio's menus and change settings needed for operation with the HRD software. ![]() Follow the manufacturer's instructions to install the drivers, or, if you have problems locating or installing the drivers, please contact the device manufacturer's support team for assistance. Connecting the cable before installing the proper driver could result in a "Generic" driver being installed by Windows which could result in issues later on. Insure you have installed the Virtual Com Port drivers for your radio or interface before connecting the USB Cable to the computer. This method requires a Virtual Com Port driver, which can be downloaded from the radio manufacturer's website. The USB interface provides for Rig Control and an Audio Codec for the radio's internal soundcard. If the cable you are currently using or plan to use doesn't have the ferrite chokes, it's recommended you purchase some of the "snap-on" chokes that are available from or on eBay and attach them to the cable you are using. These chokes help prevent RF radiation, which may be present in any shack, from feeding back into the computer, which can sometimes cause some very strange behavior in the HRD software. Notice the "Ferrite Chokes" on each end of the cable. SignaLink, Rig Blaster, Rig Expert, or other interface) is required because this USB cable provides the connection for the Rig Control and it also carries the Audio for the radio's built-in soundcard which is accessed by a "USB Audio CODEC" once the proper driver from the radio's manufacturer is installed.īelow is an image of the USB cable we recommend. The most common way of interfacing your radio to the computer is via a standard A/B type USB cable. Too much work to discern shoddy written text.Solution home Knowledgebase Radio Support IC-7300 USB Setup Configuration We’ll have to see what we can do with paddles/keyers.Īnd as a final note – if generaly skip bad cw handwriting. If you look at RSBA1 – there is no paddle / key support either, unless you use a kbd.Īt ome time in my life I used an SDR type rig with a remote display and the latencies were over 150ms which made SSB contests already a problem. We have one goal I think and that is to have a way to make CW readable at the other hand and quickly too with low latencies. Else we can say that FT* is also not real WSPR is not real, etc. I don’t even care if people use a decoder themselves. Now consider high speed cw, like 30 wpm if you have latencies and or drop outs, and you switch the rig on/off, you will have botched code as shown above and that’s when things go reasonably well. I am not aware of “-.-.–.-” being a shortcut/definition of CQ. I sometimes hear people sending this “-.-.–.-.-.–.-” – and yes I know what they mean biut ot’s now what’s being sent. The positive part of sending using the remote control CW is that if you feed the rig “PA3MET”, it will send PA3MET, exactly with all the params that are attached to it. I responded to Phil in private – I do lots of cw contests and out of 300+ contacts, I mostly use macros and if I touch the paddle once or twice, that’s it. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |